XSZ Miniature Inductive Proximity Sensor

The XSZ Miniature Inductive Proximity Sensor series provides non-contact metal detection for compact machine locations. The supplied series material lists shielded, flush-mount 3 mm, 4 mm and 5 mm diameter options, with 0.6 mm ±10% and 0.8 mm ±10% sensing-distance options. It also lists a 10–30 VDC operating range, NPN or PNP output choices, NO or NC logic choices and pre-wired connections. The exact diameter, sensing distance, output, response frequency and wiring must be matched to a specific model before selection.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response
Category:

Description

Miniature inductive sensor series overview

The XSZ Miniature Inductive Proximity Sensor series is designed for non-contact detection of metal targets at compact machine locations. The supplied series material lists shielded, flush-mount body options with 3 mm, 4 mm and 5 mm diameter designations.

This is a series overview, not a specification for one part number. Sensing distance, output logic, response frequency and mechanical fit must be checked against the selected model’s current datasheet and drawing.

Metal detection at a compact sensing point

A miniature body can help when the sensor must fit near small fixtures, machine components or moving metal parts. The supplied material lists magnetic metals as the detection target and notes that sensing distance is reduced for non-magnetic metals.

The listed sensing-distance options are 0.6 mm ±10% and 0.8 mm ±10%. Those figures are not matched to the 3, 4 or 5 mm bodies in the supplied source, so select the exact model around the real target material, geometry and mounting gap.

Series specifications and available options

The following values are transcribed from the supplied series table. They are not a confirmed combination for every unit; obtain the model-level specification before assigning a part number or designing a control circuit.

Body and detection

Diameter options3 mm, 4 mm or 5 mm; confirm the exact model and full dimensions
Mounting configurationFlush-mount, shielded, as listed for the series
Sensing-distance options0.6 mm ±10% or 0.8 mm ±10%; model mapping not supplied
Listed detectable targetMagnetic metals; sensing distance decreases for non-magnetic metals
Standard target optionsIron 4 × 4 × 1 mm or iron 5 × 5 × 1 mm; confirm which target applies to each model

Electrical, response and environment

Operating voltage10–30 VDC; 12–24 VDC nominal, as listed
Supply ripple10% peak-to-peak maximum, as listed
Current consumption10 mA maximum, as listed for the series
Load current / residual voltage100 mA maximum / 1.5 V maximum, as listed
Output optionsNPN or PNP; normally open (NO) or normally closed (NC). Confirm the actual model code for each combination.
Response-frequency range1–1.5 kHz across the supplied series; confirm the selected model and test conditions
Circuit protectionReverse power-supply polarity protection listed; confirm for the selected model
Operating temperature−25 to +55 °C, as listed
ConnectionPre-wired cable; length and wire assignment not supplied

Selecting a miniature sensor model

The supplied page does not provide a model-code matrix. Before choosing a sensor, match these requirements to the current datasheet:

  • Available mounting diameter and full body/cable-exit dimensions.
  • Actual metal target, size and position relative to the 0.6 mm or 0.8 mm sensing-distance option.
  • NPN or PNP output, NO or NC logic, controller input and approved wiring arrangement.
  • Required event rate against the selected model’s response frequency and the real target path.
  • Temperature, exposure, cable routing and any required ingress-protection grade.

Application and installation checks

These miniature inductive sensors may be evaluated for metal-part presence, position or passage checks in compact fixtures and automated equipment. For rotating or rapidly moving targets, validate target spacing and speed against the exact model’s response data; the series range alone does not establish counting accuracy.

A flush-mount designation does not replace the model-specific installation drawing. Check surrounding metal clearance, mounting depth and cable routing before fitting the sensor. The source provides no ingress-protection rating or resistance test for oil, coolant or metallic dust.

Frequently asked questions

Which miniature diameters are listed?

The supplied series material lists 3 mm, 4 mm and 5 mm body-diameter options. Confirm the actual part number and complete dimensions for the installation.

Does every model have both 0.6 mm and 0.8 mm sensing distance?

That is not established. The source lists both distances but does not map them to model codes or the two iron standard-target sizes.

Are NPN, PNP, NO and NC selectable on one sensor?

The supplied page lists these as series output options, not confirmed switchable settings. Select the exact electrical model for the controller.

Can this series be specified for oil or coolant exposure?

The supplied specifications do not state a tested ingress-protection grade or oil/coolant-resistance rating. Check the selected model’s approved environmental data before using it in such conditions.

Reviews

There are no reviews yet.

Be the first to review “XSZ Miniature Inductive Proximity Sensor”

Your email address will not be published. Required fields are marked *