SZ-M74-M30DN 74 x 48 x 15 30 mm Detection-Hole Sensor

The XSZ SZ-M74-M30DN is a 74 x 48 x 15 detection-hole sensor with a 30 mm detection-hole diameter, 4 mm minimum detection target, and NPN normally open output. The supplied 30 mm matrix also lists NPN, PNP, DC, and AC normally open or normally closed alternatives. Common source parameters include 15 mA consumption current, 100 mA maximum load current at DC 24 V, side potentiometer adjustment, and IP67 protection. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

 

Description

SZ-M74-M30DN product overview

The XSZ SZ-M74-M30DN is the NPN normally open (NO) model in a 30 mm detection-hole sensor series. Product information lists a 4 mm minimum detection target for the 30 mm selection; target material, shape and test conditions are not defined in the available information.

The series also lists NPN NC, PNP, DC and AC alternatives. These are separate part numbers with their own output or supply arrangements, not selectable settings on SZ-M74-M30DN.

ModelSZ-M74-M30DN
Detection-hole diameter30 mm
OutputNPN NO
Minimum target reference4 mm

30 mm opening and target selection

The 30 mm value is the detection-hole diameter, not the sensor’s external dimension. Match the target path and its orientation to the opening, allowing for surrounding tooling and mounting clearance. The separate housing dimension is listed as 74 × 48 × 15 in the supplied table, but that row does not state a unit.

The listed 4 mm minimum-target entry does not establish that every 4 mm object will be detected. Confirm the actual target material, shape, passage position and speed against the current product documentation and a representative application test.

Technical specifications

The values below are from the supplied product information. Confirm the current datasheet and drawing before finalizing the electrical interface or installation.

Detection and housing

Product typeDetection-hole sensor
Detection-hole diameter30 mm
Minimum detection target4 mm; target conditions to confirm
Housing dimension as listed74 × 48 × 15; drawing unit to confirm
Housing materialABS
Sensitivity adjustmentSide potentiometer

NPN model electrical data

OutputNPN, normally open (NO)
DC supply notation12–24 V (6–36 V); confirm rated and permitted ranges
Supply rippleLess than 10% peak-to-peak
Consumption current15 mA
Maximum load current100 mA at DC 24 V
Circuit protectionReverse-connection protection, surge absorption and load short-circuit protection; listed for N/P/D types

Environment and electrical safety

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Protection classIP67 (IEC)
Insulation resistanceAt least 50 MΩ at DC 500 V, between energized parts and housing
Withstand voltageAC 1000 V, 50/60 Hz for 1 minute, between energized parts and housing

Temperature and voltage influence

The supplied table states temperature influence within ±15% of sensing distance over −30 to +65 °C relative to +23 °C, and within ±10% over −25 to +60 °C relative to +23 °C. Its measurement basis is not defined for this detection-hole model.

The source also lists voltage influence as “within ±15% of rated supply-voltage range; within ±10% sensing distance at rated supply voltage.” Confirm how these two limits are intended to be read before applying either figure in a design calculation.

Related 30 mm detection-hole models

The following are separate model codes in the 30 mm series. SZ-M74-M30DN is the NPN NO selection; its output cannot be changed to another type without selecting a different model. AC variants have a separate supply category.

TypeLogicModel
NPNNOSZ-M74-M30DN — this product
NPNNCSZ-M74-M30DN2
PNPNOSZ-M74-M30DP
PNPNCSZ-M74-M30DP2
DCNOSZ-M74-M30DO
DCNCSZ-M74-M30DC
ACNOSZ-M74-M30AO
ACNCSZ-M74-M30AC

The separate AC models are listed with a 110–220 V (36–250 V), 50/60 Hz supply notation. Verify the exact supply and wiring diagram for any alternative before ordering.

Application and installation planning

A detection-hole sensor can be considered where a target is routed through a defined opening and a passage signal is required. Suitability for counting or monitoring a particular component depends on its material, geometry, travel path and speed. The supplied information does not specify response time or a validated application-specific target.

Check before specifying SZ-M74-M30DN

  • Confirm the 30 mm opening and the actual target path; test the 4 mm minimum-target reference with the intended material and shape.
  • Verify the 74 × 48 × 15 drawing unit, mounting geometry and access to the side potentiometer.
  • Check the NPN NO controller input, permitted DC supply, load current and protection requirements against the current wiring diagram.
  • Confirm cable/connector details, response time and environmental conditions for the installation.

Frequently asked questions

What does 30 mm refer to?

It is the detection-hole diameter. The separate 74 × 48 × 15 housing dimension appears without a unit in the supplied table.

Will it detect every 4 mm object?

No universal target claim is established by the available data. The listed 4 mm minimum-target figure needs confirmation for the actual material, shape and passage conditions.

Is SZ-M74-M30DN an AC model?

No. The supplied model matrix identifies it as NPN NO. AC versions have different part numbers and a separate supply category.

What details are needed to check the application?

Provide the target material and dimensions, passage position and speed, controller input, DC supply, mounting space and cable requirements.

Reviews

There are no reviews yet.

Be the first to review “SZ-M74-M30DN 74 x 48 x 15 30 mm Detection-Hole Sensor”

Your email address will not be published. Required fields are marked *