Description
SZ-M100-60DN product overview
The XSZ SZ-M100-60DN is a ring proximity sensor for metal parts passing through a 60 mm opening. It is the NPN normally open (NO) model in the 60 mm series selection and has a listed 10–30 VDC operating range.
For a machine installation, check that the target can travel through the opening, the controller accepts an NPN NO signal, and the housing and cable fit the available space. The specifications and related model codes below help narrow the selection.
| Model | SZ-M100-60DN |
|---|---|
| Detection opening | 60 mm |
| Output | NPN NO |
| Operating voltage | 10–30 VDC |
60 mm ring detection for metal parts
The 60 mm figure describes the diameter of the detection hole, not the sensor’s outside dimensions. The part’s expected path must pass through the ring with adequate clearance for its size, movement and nearby tooling.
This model is specified for metal targets. Share the actual material, part dimensions and travel speed when checking whether the sensor can provide the required detection signal. If the signal will be used for counting or process control, confirm response time for the application rather than relying on opening size alone.
Technical specifications
Compare the sensing opening, electrical interface, mounting dimensions and operating conditions together. Obtain the current SZ-M100-60DN datasheet and dimensional drawing before finalizing a purchase or machine design.
Sensing format and mechanical dimensions
| Sensor type | Proximity sensor |
|---|---|
| Product type | Ring proximity sensor |
| Detection method | In-ring detection |
| Detectable target | Metal |
| Detection-hole diameter | 60 mm |
| Housing dimensions | 100 × 81 × 50 mm |
| Mounting holes | 4 × Ø6.8 mm |
Electrical specifications
| Output configuration | NPN, normally open (NO) |
|---|---|
| Operating voltage | 10–30 VDC |
| Control input | 200 mA |
| Control output | 200 mA |
| Consumption current | Less than 10 mA |
| Residual voltage | Less than 2.5 V |
Detection performance
| Hysteresis | 1–5% |
|---|---|
| Sensing line speed | 50–3000 m/min |
| Repeat accuracy | Less than 3% |
| Response time | Confirm with XSZ for the intended application |
Environmental and construction details
| Working temperature | −25 to +70 °C |
|---|---|
| Storage temperature | −40 to +85 °C |
| Protection class | IP67 |
| Housing material | PBT / ABS |
| Indicator | Red LED |
| Cable length | 2 m |
| Circuit protection | Short-circuit protection and polarity protection |
Related 60 mm ring proximity sensor models
SZ-M100-60DN is the NPN NO product described here. The other codes are separate 60 mm selections, not operating modes of this unit. Select the model that matches the controller input and required NO or NC logic.
| Output type | Logic | Model |
|---|---|---|
| NPN | NO | SZ-M100-60DN — this product |
| NPN | NC | SZ-M100-60DN2 |
| PNP | NO | SZ-M100-60DP |
| PNP | NC | SZ-M100-60DP2 |
| DC | NO | SZ-M100-60DO |
| DC | NC | SZ-M100-60DC |
Confirm the current code and wiring diagram when selecting any alternative output model.
Applications and installation checks
Typical applications
- Detecting a metal part as it passes through the 60 mm ring opening.
- Providing a passage signal to a parts-counting station when target geometry and timing are suitable.
- Monitoring metal-part movement in automated material-handling equipment.
Installation considerations
Allow for the 100 × 81 × 50 mm housing, four Ø6.8 mm mounting holes and 2 m cable route. Keep the target’s travel path inside the ring and allow clearance around moving parts and adjacent tooling. Use the current dimensional drawing to confirm the hole pattern and indicator position.
What to confirm before ordering
- Metal target material, size and route through the 60 mm opening.
- Part speed, required detection timing and compatible controller input.
- Mounting clearance, cable length and routing.
- 10–30 VDC supply, NPN NO wiring and operating environment.
Frequently asked questions
Does 60 mm refer to the outside size of the sensor?
No. It is the detection-hole diameter. The housing dimensions listed for this selection are 100 × 81 × 50 mm.
Is SZ-M100-60DN the NPN normally open model?
Yes. SZ-M100-60DN is the NPN NO selection in the 60 mm series. Confirm the current wiring diagram before connecting it to a controller.
Can it be used for parts counting?
It may be evaluated for metal-part passage counting when the part travels through the ring. Confirm target geometry and response time against the line speed before selecting it for this task.
What information helps confirm the correct model?
Share the target material and dimensions, travel path, speed, supply voltage, controller input type and available mounting or wiring drawings.





Reviews
There are no reviews yet.