SZ-M68-30DN 30 mm Detection-Hole Sensor, NPN NO

XSZ SZ-M68-30DN is a 30 mm detection-hole sensor with a 4 mm minimum detection target and NPN normally open output. The source-listed 30 mm selection also includes NPN NC, PNP NO, and PNP NC models. The source drawing shows a 39 x 68 x 20 housing with two 5.6 mm mounting holes at 28 mm spacing. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M68-30DN product overview

The XSZ SZ-M68-30DN is a 30 mm detection-hole sensor with an NPN normally open (NO) output. Iron is the standard detection target, and the product specification lists a 4 mm minimum detection target.

Use the opening, target reference and electrical interface together when assessing a part-passage task. Confirm the actual target material, part geometry and detection timing before selecting the sensor for a machine.

ModelSZ-M68-30DN
Detection hole30 mm
Listed minimum target4 mm
OutputNPN NO

30 mm passage detection and target selection

The 30 mm figure describes the detection-hole diameter. A target moving through the opening still needs enough physical clearance for its size, position and travel path. The listed 4 mm minimum target is a reference for selection, not a promise that every 4 mm part will be detected under all conditions.

If the actual part uses a material other than iron, has an unusual shape or moves quickly, confirm suitability with XSZ using a representative target and the intended machine conditions.

Technical specifications

Review the target reference, electrical load, mounting layout and operating environment together. Request the current SZ-M68-30DN datasheet and dimensional drawing before finalizing a machine design.

Detection and mounting data

Product typeDetection-hole sensor
Detection-hole diameter30 mm
Minimum detection target4 mm, listed reference
Standard detection targetIron
Mounting holes2 × Ø5.6 mm
Mounting-hole center spacing28 mm
AdjustmentSide adjustment screw

Electrical specifications

Output configurationNPN, normally open (NO)
Operating voltage10–30 VDC
Consumption current15 mA
Load current100 mA maximum at 24 VDC
Insulation resistanceAt least 50 MΩ at 500 VDC, between energized parts and housing

Environmental limits

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Protection classIP67 (IEC)

Related 30 mm detection-hole sensor models

SZ-M68-30DN is the NPN NO product on this page. The other codes below are separate output and logic selections, not modes that can be switched on this unit.

Output typeLogicModel
NPNNOSZ-M68-30DN — this product
NPNNCSZ-M68-30DN2
PNPNOSZ-M68-30DP
PNPNCSZ-M68-30DP2

Applications and installation checks

Typical applications

  • Detecting a suitable part as it passes through a compact 30 mm opening.
  • Checking part passage at an assembly or material-handling station when the target and timing are confirmed.
  • Providing a presence signal where an NPN NO controller input is required.

Installation considerations

Mounting data lists two Ø5.6 mm holes with 28 mm center spacing and a side adjustment screw. Confirm the housing drawing, physical clearance, cable route and adjustment procedure before fixing the mounting position.

What to confirm before ordering

  • Actual target material, minimum feature size and travel path through the 30 mm hole.
  • Required detection timing, supply voltage and NPN NO input compatibility.
  • Mounting space, cable/wiring arrangement and environmental exposure.
  • Current drawing dimensions and approved sensitivity-setting instructions.

Frequently asked questions

What does the 30 mm measurement describe?

It is the diameter of the detection hole, not the full outside size of the housing. Check the current dimensional drawing for the space needed around the sensor.

Does the listed 4 mm minimum apply to every material?

Not necessarily. The product data lists iron as the standard detection target. Confirm the actual part material, shape and detection conditions before relying on the 4 mm reference.

Is SZ-M68-30DN an NPN normally open sensor?

Yes. SZ-M68-30DN is the NPN NO selection in the listed 30 mm model group. Obtain its current wiring diagram before connecting it to a controller.

What information helps confirm application fit?

Share a representative target, its material and dimensions, the path and speed through the hole, supply voltage, controller input type and available mounting space.

Reviews

There are no reviews yet.

Be the first to review “SZ-M68-30DN 30 mm Detection-Hole Sensor, NPN NO”

Your email address will not be published. Required fields are marked *