Description
SZ-M55-06DN product overview
The XSZ SZ-M55-06DN is a detection-hole sensor with a 6 mm opening. It is the NPN normally open (NO) selection in a series that also lists PNP, DC and AC models. The listed minimum detection target is 0.7 mm; confirm the target material, shape and test conditions for the intended application.
For this model, select the output and supply for the controller, then check the part path through the opening and the available mounting space. The electrical ratings and other model codes are set out below.
| Model | SZ-M55-06DN |
|---|---|
| Detection hole | 6 mm |
| Output | NPN NO |
| Minimum target reference | 0.7 mm |
6 mm detection opening and target fit
The 6 mm figure describes the opening through which a target passes. It does not describe the outside width of the housing. Check that the part’s actual path, orientation and surrounding tooling leave enough clearance around the opening.
The 0.7 mm entry is a minimum-target reference, not a guarantee that every 0.7 mm object or material will be detected. Confirm target material, dimensions and motion with XSZ before specifying the sensor for small-part passage monitoring or counting.
Technical specifications
Review the mechanical opening, NPN electrical interface and environmental values together. Obtain the current SZ-M55-06DN datasheet and drawing before finalizing a controller connection or mounting design.
Opening and housing details
| Product type | Detection-hole sensor |
|---|---|
| Detection-hole diameter | 6 mm |
| Minimum detection target | 0.7 mm; confirm target conditions |
| Housing drawing dimensions | 55 × 32 × 11; drawing unit to confirm |
| Housing material | ABS |
| Sensitivity adjustment | Side potentiometer |
NPN model electrical data
| Output configuration | NPN, normally open (NO) |
|---|---|
| DC supply notation | 12–24 V (6–36 V); confirm rated and permitted ranges |
| Supply ripple | Less than 10% peak-to-peak |
| Consumption current | 15 mA |
| Maximum load current | 100 mA at DC 24 V |
| Circuit protection | Reverse-connection protection, surge absorption and load short-circuit protection listed for N/P/D types |
Operating environment and electrical safety
| Operating and storage temperature | −30 to +65 °C; no freezing or condensation |
|---|---|
| Operating and storage humidity | 35–95% RH |
| Protection class | IP67 (IEC) |
| Insulation resistance | At least 50 MΩ at DC 500 V, between energized parts and housing |
| Withstand voltage | AC 1000 V, 50/60 Hz for 1 minute, between energized parts and housing |
Temperature and voltage influence
The listed temperature influence is within ±15% of sensing distance over −30 to +65 °C relative to +23 °C, and within ±10% over −25 to +60 °C relative to +23 °C. Confirm the measurement basis for the intended target before using these figures as design limits.
Voltage-influence wording also needs confirmation against the current datasheet before a numerical limit is applied to this model.
Related 6 mm detection-hole sensor models
SZ-M55-06DN is the NPN NO product on this page. The remaining part numbers are separate selections in the 6 mm series, not output modes of this sensor. In particular, AC models use a different supply category.
| Type | Logic | Model |
|---|---|---|
| NPN | NO | SZ-M55-06DN — this product |
| NPN | NC | SZ-M55-06DN2 |
| PNP | NO | SZ-M55-06DP |
| PNP | NC | SZ-M55-06DP2 |
| DC | NO | SZ-M55-06DO |
| DC | NC | SZ-M55-06DC |
| AC | NO | SZ-M55-06AO |
| AC | NC | SZ-M55-06AC |
Confirm the exact supply and wiring diagram for any alternative model before ordering.
Applications and installation checks
Typical applications
- Monitoring the passage of a small part through a 6 mm opening, after target testing.
- Providing a presence or passage signal in assembly equipment when the part path and response fit the process.
- Evaluating a detection point in a material-handling station where installation clearance is limited.
Installation considerations
Confirm the unit and mounting details on the current 55 × 32 × 11 housing drawing. Allow clearance for the target’s path through the 6 mm opening, the side potentiometer and the required wiring or cable route. Cable length is not specified in the available product information.
What to confirm before ordering
- Target material, shape, size and path through the 6 mm opening.
- NPN NO controller input, DC supply range, load current and wiring.
- Drawing units, installation clearance, cable type and cable length.
- Operating temperature, humidity and required response for the process.
Frequently asked questions
What does the 6 mm dimension describe?
It is the detection-hole diameter. The separate 55 × 32 × 11 housing dimension requires confirmation of its drawing unit.
Does the 0.7 mm minimum target apply to every material?
The available figure does not specify a material, shape or test method. Send the actual target details to XSZ for application confirmation.
Is SZ-M55-06DN an AC model?
No. It is the NPN NO selection in the listed matrix. The AC entries are separate models; verify the DC supply notation and wiring for SZ-M55-06DN.
What information is needed to confirm this model?
Provide the target material and dimensions, part travel path, supply and controller requirements, load current, mounting space and cable details.







Reviews
There are no reviews yet.