Description
SZ-M68-3DN product overview
The XSZ SZ-M68-3DN is a 3 mm detection-hole sensor with an NPN normally open (NO) output. The listed minimum detection target is 0.5 mm, with iron specified as the standard detection target. Its operating supply range is 10–30 VDC.
This model is intended for a detection point where a small target passes through the opening. Check the actual target material, size, alignment and controller input before selecting it; the listed minimum is not a guarantee for every material or operating condition.
| Model | SZ-M68-3DN |
|---|---|
| Detection opening | 3 mm |
| Minimum detection target | 0.5 mm, subject to target conditions |
| Output | NPN NO |
3 mm opening for small-target passage detection
The 3 mm figure describes the detection-hole diameter, not an external housing dimension. The target must pass through that opening with suitable mechanical clearance and a repeatable path. The 0.5 mm minimum-target value should be checked against the actual target material, shape and movement before it is used as a selection limit.
The standard detection target is listed as iron. If the application uses another material or a different target geometry, send XSZ a sample or the target details for confirmation rather than assuming the same detection result.
Technical specifications
Use the current SZ-M68-3DN datasheet and drawing to confirm the electrical interface, target conditions and mounting geometry before finalizing a machine design.
Detection and mounting dimensions
| Product type | Detection-hole sensor |
|---|---|
| Detection-hole diameter | 3 mm |
| Minimum detection target | 0.5 mm |
| Standard detection target | Iron |
| Drawing dimensions | 39 × 68 × 20 (confirm units and orientation on current drawing) |
| Mounting holes | 2 × Ø5.6 mm; 28 mm center spacing |
| Adjustment | Side adjustment screw |
Electrical specifications and protection
| Output configuration | NPN, normally open (NO) |
|---|---|
| Operating voltage | 10–30 VDC |
| Consumption current | 15 mA |
| Load current | 100 mA maximum at DC 24 V |
| Listed circuit protection | Reverse-connection protection, surge absorption and load short-circuit protection |
Operating environment and insulation
| Operating and storage temperature | −30 to +65 °C; no freezing or condensation |
|---|---|
| Operating and storage humidity | 35–95% RH |
| Insulation resistance | At least 50 MΩ at DC 500 V, between energized parts and housing |
| Protection class | IP67 (IEC) |
Temperature and voltage influence
| Temperature influence | −30 to +65 °C: within ±15% at +23 °C; −25 to +60 °C: within ±10% at +23 °C |
|---|---|
| Voltage influence | Within ±15% of rated supply-voltage range; within ±10% sensing distance at rated supply voltage |
Related 3 mm detection-hole sensor models
SZ-M68-3DN is the NPN NO unit described here. The other codes below are separate output selections in the 3 mm group, not switchable modes of this model.
| Output type | Logic | Model |
|---|---|---|
| NPN | NO | SZ-M68-3DN — this product |
| NPN | NC | SZ-M68-3DN2 |
| PNP | NO | SZ-M68-3DP |
| PNP | NC | SZ-M68-3DP2 |
Applications and installation checks
Typical applications
- Checking the passage of a small target through a 3 mm opening.
- Providing a part-presence signal at a compact assembly station.
- Supporting a small-part counting task after target and response-time validation.
Installation considerations
Allow for two Ø5.6 mm mounting holes at 28 mm center spacing and access to the side adjustment screw. Check the current drawing for the housing dimension units, mounting orientation and cable exit before preparing the mounting plate.
What to confirm before ordering
- Actual target material, cross-section, orientation and path through the 3 mm opening.
- The conditions behind the 0.5 mm minimum-target figure and any required response time.
- 10–30 VDC supply, NPN NO controller input and the wiring diagram.
- Drawing units, mounting clearance, cable arrangement and ambient conditions.
Frequently asked questions
What does the 3 mm dimension describe?
It is the diameter of the detection hole, not the outside size of the housing.
Does the 0.5 mm minimum apply to every target material?
Not necessarily. Iron is the listed standard target. Confirm detection with the actual material, shape and operating conditions before selecting the sensor for a 0.5 mm target.
Is SZ-M68-3DN the NPN normally open model?
Yes. SZ-M68-3DN is the NPN NO option. The NC and PNP options have their own model codes, and the current wiring diagram should be checked before connection.
What mounting information is available?
The listed drawing values are 39 × 68 × 20, with two Ø5.6 mm holes at 28 mm center spacing and a side adjustment screw. Confirm the dimension units and orientation on the current drawing.







Reviews
There are no reviews yet.