SZ-M68-6DN 6 mm Detection-Hole Sensor, NPN NO

XSZ SZ-M68-6DN is a 6 mm detection-hole sensor with a 0.7 mm minimum detection target and NPN normally open output. The source-listed 6 mm selection also includes NPN NC, PNP NO, and PNP NC models. The source drawing shows a 39 x 68 x 20 housing with two 5.6 mm mounting holes at 28 mm spacing. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M68-6DN product overview

The XSZ SZ-M68-6DN is a detection-hole sensor with a 6 mm opening and an NPN normally open (NO) output. In the listed 6 mm selection, iron is the standard detection target and 0.7 mm is the minimum-target reference.

This small opening is intended for a target that can pass through the detection hole. Match the actual material, target dimensions and travel path to the application before choosing this model; the 0.7 mm figure alone does not establish performance for every small object.

ModelSZ-M68-6DN
Detection opening6 mm
Minimum target reference0.7 mm
Output and supplyNPN NO · 10–30 VDC

6 mm opening and small-target selection

The 6 mm measurement is the detection-hole diameter. The 0.7 mm minimum-target entry is a selection reference, while iron is listed separately as the standard detection target. Target shape, material and position within the opening need to be checked for the actual part.

This model can be evaluated where a small part travels through a compact sensing point. For part counting or fast movement, confirm response time and the required controller signal before specifying the sensor; those timing values are not provided in the available product text.

Technical specifications

Check the target reference, NPN NO electrical interface and mounting drawing together. Obtain the current SZ-M68-6DN datasheet before finalizing a machine design.

Detection and mechanical dimensions

Detection-hole diameter6 mm
Minimum detection target0.7 mm (listed reference)
Standard detection targetIron
Housing drawing dimensions39 × 68 × 20 (drawing unit to confirm)
Mounting holes2 × Ø5.6 mm
Mounting-hole centre spacing28 mm
AdjustmentSide adjustment screw

Electrical specifications and protection

Output configurationNPN, normally open (NO)
Operating voltage10–30 VDC
Consumption current15 mA
Load current100 mA maximum at 24 VDC
Insulation resistanceAt least 50 MΩ at 500 VDC, between energized parts and housing
Circuit protectionReverse-connection protection, surge absorption and load short-circuit protection (listed for N.P.D type; confirm model applicability)

Operating environment and influence

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Temperature influence−30 to +65 °C: within ±15% at +23 °C; −25 to +60 °C: within ±10% at +23 °C
Voltage influenceWithin ±15% of the rated supply-voltage range; within ±10% sensing distance at rated supply voltage
Protection classIP67 (IEC)

Related 6 mm detection-hole sensor models

SZ-M68-6DN is the NPN NO unit described here. The other three codes are separate output selections for the 6 mm opening, not operating modes that can be switched on this product.

Output typeLogicModel
NPNNOSZ-M68-6DN — this product
NPNNCSZ-M68-6DN2
PNPNOSZ-M68-6DP
PNPNCSZ-M68-6DP2

Confirm the current wiring diagram for the selected output model before connecting a controller.

Applications and installation checks

Typical applications

  • Detecting a small iron part passing through a 6 mm opening, after confirming its shape and size.
  • Checking part passage in compact assembly equipment where the target path fits the sensing hole.
  • Evaluating a small-part counting point after confirming the target and required response time.

Installation considerations

The drawing lists two Ø5.6 mm mounting holes on 28 mm centres and a side adjustment screw. Verify the housing-dimension unit and cable exit on the approved drawing, then confirm clearance for the moving target and the adjustment access.

What to confirm before ordering

  • Target material, shape, minimum feature size and route through the 6 mm opening.
  • Required part speed, response time and controller input compatibility.
  • 10–30 VDC supply, NPN NO wiring, load current and cable details.
  • Housing drawing, mounting clearance and operating environment.

Frequently asked questions

What does the 6 mm dimension describe?

It is the detection-hole diameter. Check the approved drawing for the sensor’s external dimensions and mounting arrangement.

Does 0.7 mm mean it detects every 0.7 mm object?

No. It is a minimum-target reference, and the specification lists iron as the standard target. Confirm material, geometry, orientation and test conditions for the actual part.

Is SZ-M68-6DN the NPN normally open model?

Yes. The 6 mm selection lists SZ-M68-6DN as NPN NO; NPN NC and PNP NO/NC are different model codes.

What should be checked for a counting application?

Provide the target material and dimensions, travel path, machine cycle, supply voltage and controller input type. Confirm the model’s response time before using it for a required count rate.

Reviews

There are no reviews yet.

Be the first to review “SZ-M68-6DN 6 mm Detection-Hole Sensor, NPN NO”

Your email address will not be published. Required fields are marked *