Description
SZ-M68-8DN product overview
The XSZ SZ-M68-8DN is an 8 mm detection-hole sensor with an NPN normally open (NO) output. Its compact opening is intended for a target passing through the detection hole, with the listed data using iron as the standard detection target.
The 8 mm model information lists a 0.7 mm minimum detection target, a 10–30 VDC supply and four NPN/PNP output selections. For this NPN NO model, match the real target and controller input to the application before choosing the sensor.
| Model | SZ-M68-8DN |
|---|---|
| Detection opening | 8 mm |
| Output | NPN NO |
| Listed minimum target | 0.7 mm |
8 mm opening and small-target selection
The 8 mm figure is the detection-hole diameter, not the outside housing size. Check that the part can travel through the opening with clearance for its movement, alignment and nearby machine parts.
The listed 0.7 mm minimum target and iron reference are useful starting points, but they do not establish detection for every material or target shape. Share the actual part dimensions, material and path with XSZ when confirming the selection.
Technical specifications
Review the target reference, electrical interface, mounting details and environment together. Ask for the current SZ-M68-8DN datasheet and dimensional drawing before finalizing the machine design.
Detection target and mechanical details
| Detection-hole diameter | 8 mm |
|---|---|
| Minimum detection target | 0.7 mm |
| Standard detection target | Iron |
| Housing dimensions | 39 × 68 × 20 (drawing unit to confirm) |
| Mounting holes | 2 × Ø5.6 mm |
| Hole center spacing | 28 mm |
| Adjustment | Side adjustment screw |
Electrical specifications and protection
| Output configuration | NPN, normally open (NO) |
|---|---|
| Operating voltage | 10–30 VDC |
| Consumption current | 15 mA |
| Load current | 100 mA maximum at 24 VDC |
| Circuit protection | N.P.D type: reverse-connection protection, surge absorption and load short-circuit protection |
| Insulation resistance | At least 50 MΩ at 500 VDC, between energized parts and housing |
Environment and stability data
| Operating and storage temperature | −30 to +65 °C; no freezing or condensation |
|---|---|
| Operating and storage humidity | 35–95% RH |
| Temperature influence, −30 to +65 °C | Within ±15% at +23 °C reference |
| Temperature influence, −25 to +60 °C | Within ±10% at +23 °C reference |
| Voltage influence | Within ±15% of the rated supply-voltage range; within ±10% sensing distance at rated supply voltage |
| Protection class | IP67 (IEC) |
Related 8 mm detection-hole sensor models
SZ-M68-8DN is the NPN NO product on this page. The three other 8 mm codes below are separate output selections, not settings on this unit.
| Output type | Logic | Model |
|---|---|---|
| NPN | NO | SZ-M68-8DN — this product |
| NPN | NC | SZ-M68-8DN2 |
| PNP | NO | SZ-M68-8DP |
| PNP | NC | SZ-M68-8DP2 |
Confirm the current code and wiring diagram if the controller requires another output type or logic.
Applications and installation checks
Typical applications
- Detecting a small part as it passes through an 8 mm opening.
- Providing a passage signal in compact assembly equipment when the actual target meets the detection conditions.
- Monitoring small-part movement at a material-handling station after target and timing checks.
Installation considerations
The dimensional drawing identifies two Ø5.6 mm mounting holes on 28 mm centers and a side adjustment screw. Check the current drawing for overall dimensions and units, the target path through the hole, cable routing and clearance around adjacent equipment.
What to confirm before ordering
- Actual target material, shape and size; compare with the iron reference and listed 0.7 mm minimum.
- Travel path, required detection timing and controller input type.
- Drawing units, mounting clearance, cable and wiring details.
- 10–30 VDC supply, load current and operating environment.
Frequently asked questions
What does the 8 mm dimension describe?
It is the detection-hole diameter, not the outside size of the sensor housing.
Does the 0.7 mm minimum apply to every material?
The 0.7 mm value is listed with iron as the standard detection target. Confirm the actual material, shape and test conditions before relying on that minimum for another target.
Is SZ-M68-8DN the NPN normally open model?
Yes. SZ-M68-8DN is the NPN NO selection in the four-model 8 mm group. Check the current wiring diagram before connecting it to a controller.
What mounting information is available?
The dimensional drawing lists two Ø5.6 mm holes at 28 mm center spacing and a side adjustment screw. Confirm the overall-dimension units from the current drawing.






Reviews
There are no reviews yet.