SZ-M68-15DN 15 mm Detection-Hole Sensor, NPN NO

XSZ SZ-M68-15DN is a 15 mm detection-hole sensor with a 2 mm minimum detection target and NPN normally open output. The source-listed 15 mm selection also includes NPN NC, PNP NO, and PNP NC models. The source drawing shows a 39 x 68 x 20 housing with two 5.6 mm mounting holes at 28 mm spacing. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M68-15DN product overview

The XSZ SZ-M68-15DN is a detection-hole sensor with a 15 mm opening and an NPN normally open (NO) output. The listed standard detection target is iron, with a 2 mm minimum detection target. This model operates from a 10–30 VDC supply.

It is intended for applications where a part passes through the opening. Select it against the actual target material and size, controller input, available mounting space and required detection timing.

ModelSZ-M68-15DN
Detection opening15 mm
Listed minimum target2 mm
OutputNPN NO

15 mm opening and small-target detection

The 15 mm measurement describes the detection-hole diameter. The product information lists a 2 mm minimum detection target and iron as the standard target; these are selection references, not a guarantee that every 2 mm part or every metal will be detected under all conditions.

Check the part’s actual material, shape, orientation and travel path through the opening. When the signal will be used for counting or machine control, confirm the response time and target conditions for that process.

Technical specifications

Review the detection target, output, installation dimensions and environmental limits together. Use the current SZ-M68-15DN datasheet and drawing to confirm the final machine fit.

Detection target and mechanical layout

Detection-hole diameter15 mm
Minimum detection target2 mm, as listed
Standard detection targetIron
Housing drawing dimensions39 × 68 × 20 (confirm drawing units)
Mounting holes2 × Ø5.6 mm; 28 mm centre spacing
AdjustmentSide adjustment screw

Electrical specifications

Output configurationNPN, normally open (NO)
Operating voltage10–30 VDC
Consumption current15 mA
Load current100 mA maximum at 24 VDC
Circuit protectionN.P.D type: reverse-connection protection, surge absorption and load short-circuit protection

Detection and supply influence

Temperature influence−30 to +65 °C: within ±15% at +23 °C; −25 to +60 °C: within ±10% at +23 °C
Voltage influenceWithin ±15% of rated supply-voltage range; within ±10% sensing distance at rated supply voltage
Response timeConfirm for the intended target and line speed

Environmental and insulation ratings

Ambient temperatureOperating and storage: −30 to +65 °C; no freezing or condensation
Ambient humidityOperating and storage: 35–95% RH
Insulation resistanceAt least 50 MΩ at 500 VDC, between energized parts and housing
Protection classIP67 (IEC)

Related 15 mm detection-hole sensor models

SZ-M68-15DN is the NPN NO model described here. The other part numbers below are separate 15 mm selections, not output modes that can be switched on this unit.

Output typeLogicModel
NPNNOSZ-M68-15DN — this product
NPNNCSZ-M68-15DN2
PNPNOSZ-M68-15DP
PNPNCSZ-M68-15DP2

Confirm the wiring diagram for the selected output and logic before connecting it to the controller.

Applications and installation checks

Typical applications

  • Checking whether a small part passes through the 15 mm opening.
  • Providing a part-passage signal in compact assembly equipment when the target and timing are suitable.
  • Monitoring part movement at a material-handling station with a compatible target path.

Installation considerations

The drawing lists a 39 × 68 × 20 housing, two Ø5.6 mm mounting holes with 28 mm centre spacing, and a side adjustment screw. Verify the housing-dimension units and mounting pattern on the approved drawing. Leave enough clearance for the target’s path and the required cable route.

What to confirm before ordering

  • Target material, size, shape and path through the 15 mm opening.
  • NPN NO controller input, supply voltage and required detection timing.
  • Mounting clearance, approved drawing dimensions, cable length and wiring route.
  • Temperature, humidity and protection requirements of the installation.

Frequently asked questions

What does the 15 mm dimension describe?

It is the diameter of the detection opening, not the outside size of the housing.

Will it detect every 2 mm metal part?

The listed minimum detection target is 2 mm, and iron is the standard target. Confirm the test conditions and your part’s material, shape and orientation before relying on this figure.

Is SZ-M68-15DN the NPN normally open version?

Yes. The 15 mm model matrix identifies SZ-M68-15DN as NPN NO. Select another part number if PNP or NC logic is required.

What information is needed to check installation fit?

Provide the target details, passage speed, controller input, supply voltage, mounting drawing and cable requirements. Confirm the current housing-dimension units and wiring diagram before ordering.

Reviews

There are no reviews yet.

Be the first to review “SZ-M68-15DN 15 mm Detection-Hole Sensor, NPN NO”

Your email address will not be published. Required fields are marked *