SZ-M68-8DN 8 mm Detection-Hole Sensor, NPN NO

XSZ SZ-M68-8DN is an 8 mm detection-hole sensor with a 0.7 mm minimum detection target and NPN normally open output. The source-listed 8 mm selection also includes NPN NC, PNP NO, and PNP NC models. The source drawing shows a 39 x 68 x 20 housing with two 5.6 mm mounting holes at 28 mm spacing. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M68-8DN product overview

The XSZ SZ-M68-8DN is an 8 mm detection-hole sensor with an NPN normally open (NO) output. Its compact opening is intended for a target passing through the detection hole, with the listed data using iron as the standard detection target.

The 8 mm model information lists a 0.7 mm minimum detection target, a 10–30 VDC supply and four NPN/PNP output selections. For this NPN NO model, match the real target and controller input to the application before choosing the sensor.

ModelSZ-M68-8DN
Detection opening8 mm
OutputNPN NO
Listed minimum target0.7 mm

8 mm opening and small-target selection

The 8 mm figure is the detection-hole diameter, not the outside housing size. Check that the part can travel through the opening with clearance for its movement, alignment and nearby machine parts.

The listed 0.7 mm minimum target and iron reference are useful starting points, but they do not establish detection for every material or target shape. Share the actual part dimensions, material and path with XSZ when confirming the selection.

Technical specifications

Review the target reference, electrical interface, mounting details and environment together. Ask for the current SZ-M68-8DN datasheet and dimensional drawing before finalizing the machine design.

Detection target and mechanical details

Detection-hole diameter8 mm
Minimum detection target0.7 mm
Standard detection targetIron
Housing dimensions39 × 68 × 20 (drawing unit to confirm)
Mounting holes2 × Ø5.6 mm
Hole center spacing28 mm
AdjustmentSide adjustment screw

Electrical specifications and protection

Output configurationNPN, normally open (NO)
Operating voltage10–30 VDC
Consumption current15 mA
Load current100 mA maximum at 24 VDC
Circuit protectionN.P.D type: reverse-connection protection, surge absorption and load short-circuit protection
Insulation resistanceAt least 50 MΩ at 500 VDC, between energized parts and housing

Environment and stability data

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Temperature influence, −30 to +65 °CWithin ±15% at +23 °C reference
Temperature influence, −25 to +60 °CWithin ±10% at +23 °C reference
Voltage influenceWithin ±15% of the rated supply-voltage range; within ±10% sensing distance at rated supply voltage
Protection classIP67 (IEC)

Related 8 mm detection-hole sensor models

SZ-M68-8DN is the NPN NO product on this page. The three other 8 mm codes below are separate output selections, not settings on this unit.

Output typeLogicModel
NPNNOSZ-M68-8DN — this product
NPNNCSZ-M68-8DN2
PNPNOSZ-M68-8DP
PNPNCSZ-M68-8DP2

Confirm the current code and wiring diagram if the controller requires another output type or logic.

Applications and installation checks

Typical applications

  • Detecting a small part as it passes through an 8 mm opening.
  • Providing a passage signal in compact assembly equipment when the actual target meets the detection conditions.
  • Monitoring small-part movement at a material-handling station after target and timing checks.

Installation considerations

The dimensional drawing identifies two Ø5.6 mm mounting holes on 28 mm centers and a side adjustment screw. Check the current drawing for overall dimensions and units, the target path through the hole, cable routing and clearance around adjacent equipment.

What to confirm before ordering

  • Actual target material, shape and size; compare with the iron reference and listed 0.7 mm minimum.
  • Travel path, required detection timing and controller input type.
  • Drawing units, mounting clearance, cable and wiring details.
  • 10–30 VDC supply, load current and operating environment.

Frequently asked questions

What does the 8 mm dimension describe?

It is the detection-hole diameter, not the outside size of the sensor housing.

Does the 0.7 mm minimum apply to every material?

The 0.7 mm value is listed with iron as the standard detection target. Confirm the actual material, shape and test conditions before relying on that minimum for another target.

Is SZ-M68-8DN the NPN normally open model?

Yes. SZ-M68-8DN is the NPN NO selection in the four-model 8 mm group. Check the current wiring diagram before connecting it to a controller.

What mounting information is available?

The dimensional drawing lists two Ø5.6 mm holes at 28 mm center spacing and a side adjustment screw. Confirm the overall-dimension units from the current drawing.

Reviews

There are no reviews yet.

Be the first to review “SZ-M68-8DN 8 mm Detection-Hole Sensor, NPN NO”

Your email address will not be published. Required fields are marked *