Description
SZ-M68-12DN product overview
The XSZ SZ-M68-12DN is a 12 mm detection-hole sensor with an NPN normally open (NO) output. Its listed operating range is 10–30 VDC. The 12 mm aperture provides a defined passage for the target, while the surrounding housing and mounting pattern must fit the machine layout.
The product data lists a 1.2 mm minimum detection target and iron as the standard detection target. Confirm the actual target material, geometry and travel path before selecting this model; a minimum-size entry does not establish detection of every object of that size.
| Model | SZ-M68-12DN |
|---|---|
| Detection-hole diameter | 12 mm |
| Output | NPN NO |
| Standard detection target | Iron |
12 mm aperture and small-target selection
The 12 mm figure describes the detection-hole diameter. Select it around the target’s full path through the opening, allowing clearance for part variation, guiding hardware and machine movement.
A 1.2 mm minimum detection target is listed for the 12 mm selection, but the test target’s shape and conditions are not specified. Use the iron reference target as a starting point and confirm the real part in the intended position. If the signal will drive counting or control, also confirm the required response timing.
Technical specifications
Review the detection target, electrical load, mounting arrangement and environment together. Request the current SZ-M68-12DN datasheet, wiring diagram and dimensional drawing before fixing the machine design.
Detection and mechanical dimensions
| Detection-hole diameter | 12 mm |
|---|---|
| Minimum detection target | 1.2 mm; confirm target and test conditions |
| Standard detection target | Iron |
| Housing dimensions | 39 × 68 × 20; confirm dimensional units |
| Mounting holes | 2 × Ø5.6 mm |
| Mounting-hole spacing | 28 mm center-to-center |
| Adjustment | Side adjustment screw |
Electrical specifications
| Output configuration | NPN, normally open (NO) |
|---|---|
| Operating voltage | 10–30 VDC |
| Consumption current | 15 mA |
| Load current | 100 mA maximum at 24 VDC |
| Circuit protection | Reverse-connection protection, surge absorption and load short-circuit protection; confirm “N.P.D type” applicability |
| Insulation resistance | At least 50 MΩ at 500 VDC, between energized parts and housing |
Operating environment and influence data
| Operating and storage temperature | −30 to +65 °C; no freezing or condensation |
|---|---|
| Operating and storage humidity | 35–95% RH |
| Temperature influence | −30 to +65 °C: within ±15% at +23 °C; −25 to +60 °C: within ±10% at +23 °C. Confirm the measurement basis. |
| Voltage influence | Within ±15% of rated supply-voltage range; within ±10% sensing distance at rated supply voltage. Confirm the measurement basis. |
| Protection class | IP67 (IEC) |
Related 12 mm detection-hole sensor models
SZ-M68-12DN is the NPN NO product on this page. The other codes below are separate 12 mm selections, not output settings that can be switched on this unit.
| Output type | Logic | Model |
|---|---|---|
| NPN | NO | SZ-M68-12DN — this product |
| NPN | NC | SZ-M68-12DN2 |
| PNP | NO | SZ-M68-12DP |
| PNP | NC | SZ-M68-12DP2 |
Applications and installation checks
Typical applications
The 12 mm format can be evaluated where a small iron reference target passes through a defined opening, such as a compact part-passage or assembly station. Confirm the real part and process conditions before treating it as a counting or control point.
Installation considerations
The mounting data shows two Ø5.6 mm holes spaced 28 mm center-to-center and a side adjustment screw. Verify the housing’s dimensional units on the current drawing, then check target clearance, access to the adjustment point and the actual cable or connector arrangement before mounting.
What to confirm before ordering
- Target material, shape, size and route through the 12 mm hole.
- NPN NO controller input, load current and verified wiring diagram.
- Required detection timing, mounting clearance and drawing dimensions.
- Temperature, humidity, cable or connector needs and required quantity.
Frequently asked questions
What does the 12 mm dimension describe?
It is the detection-hole diameter, not the outside housing size. The listed housing dimensions are 39 × 68 × 20; confirm their unit from the current drawing.
Can it detect every 1.2 mm object?
Not necessarily. The listed 1.2 mm minimum does not define every target material or shape. Iron is the standard detection target; check the actual part and test conditions before selection.
Is SZ-M68-12DN the NPN normally open model?
Yes. SZ-M68-12DN is the NPN NO selection in the 12 mm group. Confirm its wiring diagram and the load requirement before connecting it.
What should be provided for model confirmation?
Send the target material and dimensions, its path through the hole, supply voltage, controller input requirement, installation drawing and expected movement speed.







Reviews
There are no reviews yet.