LJ30A3-15-Z/BX 15 mm Non-shielded Proximity Sensor

The XSZ LJ30A3-15-Z/BX is a non-shielded DC proximity sensor with NPN normally open output and a 15 mm +/-10% sensing distance. The supplied non-shielded matrix also lists NPN and PNP NO, NC, and NO+NC options, plus DC two-wire and AC two-wire models. Confirm dimensions, cable, wiring, and target compatibility with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

LJ30A3-15-Z/BX product overview

The XSZ LJ30A3-15-Z/BX is an M30, non-shielded proximity sensor for metal-target detection. This specific model has a DC NPN normally open (NO) output. Its listed 15 mm ±10% sensing distance is based on an iron reference target; actual detection distance depends on the target and installation conditions.

Use the 0–13 mm setting-distance entry when planning the gap, then verify the real part in its operating position. The NPN NO output must match the controller input and the confirmed wiring diagram.

ModelLJ30A3-15-Z/BX
Body sizeM30
Sensing distance15 mm ±10%, non-shielded
OutputDC NPN, normally open (NO)

15 mm non-shielded sensing and target selection

The supplied reference specifies an iron plate measuring 54 × 54 × 1 mm as the standard detection target. The 15 mm sensing-distance figure and 0–13 mm setting-distance range should be checked against that reference, not treated as a promise for every metal part.

Magnetic metal is the stated detectable-target category. The source notes reduced sensing distance for non-magnetic metals. Check the actual target material, face size, orientation and travel path before setting the final gap.

Technical specifications

The figures below come from the supplied LJ30A3-15 series reference. Confirm the current BX-specific datasheet and wiring diagram before fixing electrical limits or machine clearances.

Detection and mechanical data

Mounting diameterM30
ShieldingNon-shielded
Sensing distance15 mm ±10%
Setting distance0–13 mm
Standard detection targetIron, 54 × 54 × 1 mm
HysteresisLess than 10% of sensing distance
Housing / sensing faceNickel-plated brass / ABS

DC NPN electrical data

Output logicNPN normally open (NO)
Listed DC supply12–24 VDC; confirm the separate 6–36 V range before use
Response frequency, DC type0.5 kHz
Consumption current, N.P typeLess than 13 mA
Control-output figure, N.P typeLess than 300 mA; confirm the permitted load rating
Insulation resistanceAt least 50 MΩ at 500 VDC, between energized parts and housing

Environment and protection

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Humidity35–95% RH
Protection classIP67

Related LJ30A3-15 output models

LJ30A3-15-Z/BX is the DC NPN NO product on this page. The codes below represent separate models; their outputs and supply types are not switchable settings on the BX unit.

Electrical typeOutputLogicModel
DCNPNNOLJ30A3-15-Z/BX — this product
DCNPNNCLJ30A3-15-Z/AX
DCNPNNO+NCLJ30A3-15-Z/CX
DCPNPNOLJ30A3-15-Z/BY
DCPNPNCLJ30A3-15-Z/AY
DCPNPNO+NCLJ30A3-15-Z/CY
DC two-wire—NOLJ30A3-15-Z/EX
DC two-wire—NCLJ30A3-15-Z/DX
AC two-wire—NOLJ30A3-15-J/EZ
AC two-wire—NCLJ30A3-15-J/DZ

Applications and installation checks

Metal-target detection

Evaluate this M30 sensor where a defined metal part approaches the sensing face and the controller requires an NPN NO signal. Typical selection work includes checking part position at a fixture, travel point or machine stop; confirm the real target and detection gap in the assembled machine.

Mounting and electrical fit

A non-shielded sensing face needs mounting clearance appropriate to the manufacturer’s drawing. Verify the M30 body envelope, nearby metal, target approach, cable or connector arrangement and the exact wiring colors before installation. The source does not specify a cable length or connection drawing for BX.

Confirm before ordering

  • Target material, size, orientation and operating gap.
  • DC NPN NO controller input, allowed supply range and output load.
  • M30 mounting space, nearby metal and verified wiring connection.
  • Required response rate, environment, cable or connector and quantity.

Frequently asked questions

Is LJ30A3-15-Z/BX an NPN normally open sensor?

Yes. The supplied model matrix identifies BX as the DC NPN NO version. PNP, NC and two-wire outputs use different model codes.

Will every metal target be detected at 15 mm?

No universal 15 mm distance is established for every metal. The rating uses a 54 × 54 × 1 mm iron reference target; the source notes reduced distance for non-magnetic metals.

Can I use the AC supply values listed for this series?

No. BX is the DC NPN version. The AC two-wire entries belong to separate J-series models and should not be applied to this sensor.

What should be checked for installation?

Check the real target and gap, non-shielded mounting clearance, controller input, verified DC supply and load limits, and the BX wiring/cable specification.

Reviews

There are no reviews yet.

Be the first to review “LJ30A3-15-Z/BX 15 mm Non-shielded Proximity Sensor”

Your email address will not be published. Required fields are marked *