LJ12A3-4-Z/BX 4 mm Non-shielded Proximity Sensor

The XSZ LJ12A3-4-Z/BX is a non-shielded DC proximity sensor with NPN normally open output and a 4 mm +/-10% sensing distance. The supplied non-shielded matrix also lists NPN and PNP NO, NC, and NO+NC options, plus DC two-wire and AC two-wire models. Confirm dimensions, cable, wiring, and target compatibility with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

LJ12A3-4-Z/BX product overview

The XSZ LJ12A3-4-Z/BX is a non-shielded inductive proximity sensor with a DC NPN normally open (NO) output. The listed sensing distance is 4 mm ±10%, with a setting-distance range of 0–3.6 mm under the supplied reference conditions.

The standard detection target is iron measuring 15 × 15 × 1 mm. Detection distance decreases for non-magnetic metals, so confirm the actual target material, size and mounting arrangement before finalizing the sensor position.

4 mm non-shielded metal detection

The 4 mm value is a sensing-distance specification, not the diameter of the sensor. The product table identifies its dimension class as M12. The full body length and installation clearances are not stated in the available information; use the current mechanical drawing for mounting design.

The 0–3.6 mm setting range gives a separate installation reference. Check target variation, sensor-to-target alignment and nearby metal against the actual application before setting a switching point.

Technical specifications

The following values are listed in the available product information. Confirm the latest LJ12A3-4-Z/BX datasheet and wiring diagram before using them as installation or controller-design limits.

Sensing and construction

Sensing method and mounting typeInductive, non-shielded
Dimension designationM12; full mechanical dimensions to confirm
Sensing distance4 mm ±10%
Setting distance0–3.6 mm
Standard detection targetIron, 15 × 15 × 1 mm
Detectable targetMagnetic metal; shorter sensing distance for non-magnetic metals
HysteresisLess than 10% of sensing distance
Housing / sensing faceNickel-plated brass / ABS
Protection classIP67

NPN NO electrical data

Output configurationDC NPN, normally open (NO)
DC supply notationDC 12–24 V (6–36 V); confirm the meaning of both ranges
Supply rippleLess than 10% peak-to-peak
N/P-type consumption currentLess than 13 mA
N/P-type control outputLess than 300 mA
DC response frequency0.5 kHz
N/P/D-type circuit protectionReverse-connection protection, surge absorption and load short-circuit protection

Operating environment and insulation

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Insulation resistanceAt least 50 MΩ at DC 500 V, between energized parts and housing

The supplied temperature-influence entries refer to sensing-distance change relative to +23 °C: within ±15% over −30 to +65 °C and within ±10% over −25 to +60 °C. Confirm the test basis and the separate voltage-influence wording against the current datasheet before treating either as a design limit.

Related non-shielded 4 mm models

LJ12A3-4-Z/BX is the DC NPN NO sensor described on this page. The following codes are separate electrical and output selections, not modes that can be changed on this unit. The AC two-wire choices have a different supply category.

Electrical typeOutputLogicModel
DCNPNNOLJ12A3-4-Z/BX — this product
DCNPNNCLJ12A3-4-Z/AX
DCNPNNO+NCLJ12A3-4-Z/CX
DCPNPNOLJ12A3-4-Z/BY
DCPNPNCLJ12A3-4-Z/AY
DCPNPNO+NCLJ12A3-4-Z/CY
DCTwo-wireNOLJ12A3-4-Z/EX
DCTwo-wireNCLJ12A3-4-Z/DX
ACTwo-wireNOLJ12A3-4-J/EZ
ACTwo-wireNCLJ12A3-4-J/DZ

Confirm the exact supply, load and wiring for any alternative model. The source lists AC 110–220 V (36–250 V), 50/60 Hz and 25 Hz response for the separate AC types; these are not specifications for LJ12A3-4-Z/BX.

Applications and installation checks

Potential applications

  • Detecting a defined iron or other magnetic-metal target at a repeatable machine position.
  • Providing an NPN NO signal to a compatible DC controller input after the load and wiring are checked.
  • Monitoring a metal part in compact equipment where the M12 designation fits the mechanical design.

Before installation or ordering

Confirm the target material, shape, travel variation and working gap against the 0–3.6 mm setting range. Obtain the current M12 body drawing for full length and non-shielded mounting clearance. Check the DC supply notation, controller input, load current, cable or connector and wiring diagram for the `/BX` model. The supplied source does not specify cable length or connection colors.

Frequently asked questions

Is LJ12A3-4-Z/BX NPN or PNP?

The supplied model matrix identifies `/BX` as the DC NPN normally open option. PNP and other output configurations have different part numbers.

How do the 4 mm and 0–3.6 mm figures differ?

The first is the listed sensing distance with ±10% tolerance; the second is the setting-distance range. Check both against the actual target and installation conditions.

Will it sense non-magnetic metals at 4 mm?

The available data says sensing distance decreases for non-magnetic metals but does not give a correction factor. Verify the chosen target and working gap.

What mechanical and electrical details remain to be confirmed?

Confirm the full M12 drawing, non-shielded mounting clearance, the DC supply ranges, cable or connector, wiring diagram and controller load compatibility for `/BX`.

Reviews

There are no reviews yet.

Be the first to review “LJ12A3-4-Z/BX 4 mm Non-shielded Proximity Sensor”

Your email address will not be published. Required fields are marked *