SZ-M68-12DN 12 mm Detection-Hole Sensor, NPN NO

XSZ SZ-M68-12DN is a 12 mm detection-hole sensor with a 1.2 mm minimum detection target and NPN normally open output. The source-listed 12 mm selection also includes NPN NC, PNP NO, and PNP NC models. The source drawing shows a 39 x 68 x 20 housing with two 5.6 mm mounting holes at 28 mm spacing. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M68-12DN product overview

The XSZ SZ-M68-12DN is a 12 mm detection-hole sensor with an NPN normally open (NO) output. Its listed operating range is 10–30 VDC. The 12 mm aperture provides a defined passage for the target, while the surrounding housing and mounting pattern must fit the machine layout.

The product data lists a 1.2 mm minimum detection target and iron as the standard detection target. Confirm the actual target material, geometry and travel path before selecting this model; a minimum-size entry does not establish detection of every object of that size.

ModelSZ-M68-12DN
Detection-hole diameter12 mm
OutputNPN NO
Standard detection targetIron

12 mm aperture and small-target selection

The 12 mm figure describes the detection-hole diameter. Select it around the target’s full path through the opening, allowing clearance for part variation, guiding hardware and machine movement.

A 1.2 mm minimum detection target is listed for the 12 mm selection, but the test target’s shape and conditions are not specified. Use the iron reference target as a starting point and confirm the real part in the intended position. If the signal will drive counting or control, also confirm the required response timing.

Technical specifications

Review the detection target, electrical load, mounting arrangement and environment together. Request the current SZ-M68-12DN datasheet, wiring diagram and dimensional drawing before fixing the machine design.

Detection and mechanical dimensions

Detection-hole diameter12 mm
Minimum detection target1.2 mm; confirm target and test conditions
Standard detection targetIron
Housing dimensions39 × 68 × 20; confirm dimensional units
Mounting holes2 × Ø5.6 mm
Mounting-hole spacing28 mm center-to-center
AdjustmentSide adjustment screw

Electrical specifications

Output configurationNPN, normally open (NO)
Operating voltage10–30 VDC
Consumption current15 mA
Load current100 mA maximum at 24 VDC
Circuit protectionReverse-connection protection, surge absorption and load short-circuit protection; confirm “N.P.D type” applicability
Insulation resistanceAt least 50 MΩ at 500 VDC, between energized parts and housing

Operating environment and influence data

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Temperature influence−30 to +65 °C: within ±15% at +23 °C; −25 to +60 °C: within ±10% at +23 °C. Confirm the measurement basis.
Voltage influenceWithin ±15% of rated supply-voltage range; within ±10% sensing distance at rated supply voltage. Confirm the measurement basis.
Protection classIP67 (IEC)

Related 12 mm detection-hole sensor models

SZ-M68-12DN is the NPN NO product on this page. The other codes below are separate 12 mm selections, not output settings that can be switched on this unit.

Output typeLogicModel
NPNNOSZ-M68-12DN — this product
NPNNCSZ-M68-12DN2
PNPNOSZ-M68-12DP
PNPNCSZ-M68-12DP2

Applications and installation checks

Typical applications

The 12 mm format can be evaluated where a small iron reference target passes through a defined opening, such as a compact part-passage or assembly station. Confirm the real part and process conditions before treating it as a counting or control point.

Installation considerations

The mounting data shows two Ø5.6 mm holes spaced 28 mm center-to-center and a side adjustment screw. Verify the housing’s dimensional units on the current drawing, then check target clearance, access to the adjustment point and the actual cable or connector arrangement before mounting.

What to confirm before ordering

  • Target material, shape, size and route through the 12 mm hole.
  • NPN NO controller input, load current and verified wiring diagram.
  • Required detection timing, mounting clearance and drawing dimensions.
  • Temperature, humidity, cable or connector needs and required quantity.

Frequently asked questions

What does the 12 mm dimension describe?

It is the detection-hole diameter, not the outside housing size. The listed housing dimensions are 39 × 68 × 20; confirm their unit from the current drawing.

Can it detect every 1.2 mm object?

Not necessarily. The listed 1.2 mm minimum does not define every target material or shape. Iron is the standard detection target; check the actual part and test conditions before selection.

Is SZ-M68-12DN the NPN normally open model?

Yes. SZ-M68-12DN is the NPN NO selection in the 12 mm group. Confirm its wiring diagram and the load requirement before connecting it.

What should be provided for model confirmation?

Send the target material and dimensions, its path through the hole, supply voltage, controller input requirement, installation drawing and expected movement speed.

Reviews

There are no reviews yet.

Be the first to review “SZ-M68-12DN 12 mm Detection-Hole Sensor, NPN NO”

Your email address will not be published. Required fields are marked *