Description
SZ-M137-105DN product overview
The XSZ SZ-M137-105DN is a ring proximity sensor for detecting metal targets as they pass through a 105 mm opening. This specific model has an NPN normally open (NO) output and operates from a 10–30 VDC supply.
The pass-through format can be considered for metal-part passage detection, parts-counting stations and automated material-handling equipment when the target and operating conditions match the installation.
| Model | SZ-M137-105DN |
|---|---|
| Detection opening | 105 mm |
| Output | NPN NO |
| Supply | 10–30 VDC |
105 mm ring detection for metal parts
Use the 105 mm opening when the part and its travel path can pass through the ring with suitable clearance. The sensor is specified for metal targets; target geometry, orientation and movement should be checked against the required detection result.
Check that the controller input is compatible with an NPN normally open signal. The listed 2 m cable, housing size and mounting-hole dimensions also need to fit the planned location. Obtain the wiring diagram and confirm response time for the intended application.
Technical specifications
Review the electrical, mechanical and environmental values together before selecting the sensor. Confirm the current specification and drawing for SZ-M137-105DN when making a purchase or machine-design decision.
Product type and mechanical dimensions
| Sensor type | Proximity sensor |
|---|---|
| Product type | Ring proximity sensor |
| Detection method | In-ring detection |
| Detectable target | Metal |
| Detection-hole diameter | 105 mm |
| Housing dimensions | 137 × 115.5 × 54 mm |
| Mounting holes | 4 × Ø8.8 mm |
Electrical specifications
| Output configuration | NPN, normally open (NO) |
|---|---|
| Operating voltage | 10–30 VDC |
| Control input | 200 mA |
| Control output | 200 mA |
| Consumption current | Less than 10 mA |
| Residual voltage | Less than 2.5 V |
Detection performance
| Hysteresis | 1–5% |
|---|---|
| Sensing line speed | 50–3000 m/min |
| Repeat accuracy | Less than 3% |
| Response time | Confirm with XSZ for the intended application |
Environmental and construction details
| Working temperature | −25 to +70 °C |
|---|---|
| Storage temperature | −40 to +85 °C |
| Protection class | IP67 |
| Housing material | PBT / ABS |
| Indicator | Red LED |
| Cable length | 2 m |
| Circuit protection | Short-circuit protection and polarity protection |
Related 105 mm ring proximity sensor models
SZ-M137-105DN is the NPN NO product on this page. The other part numbers below are separate 105 mm selections, not switchable operating modes of this unit.
| Output type | Logic | Model |
|---|---|---|
| NPN | NO | SZ-M137-105DN — this product |
| NPN | NC | SZ-M137-105DN2 |
| PNP | NO | SZ-M137-105DP |
| PNP | NC | SZ-M137-105DP2 |
| DC | NO | SZ-M137-105DO |
| DC | NC | SZ-M137-105DC |
Confirm the wiring and output definition of any alternative model before ordering, especially the configurations labeled “DC”.
Applications and installation checks
Typical applications
- Detecting a metal part as it travels through a circular opening.
- Providing a passage signal for a parts-counting station, subject to controller and timing checks.
- Monitoring metal-part movement in automated material-handling equipment.
What to confirm before ordering
- Target material, size and position within the 105 mm opening.
- Required line speed, detection timing and controller input type.
- Mounting clearance for the housing and four Ø8.8 mm holes.
- Supply, NPN NO wiring, cable route and operating environment.
Frequently asked questions
What does the 105 mm dimension describe?
It is the detection-hole diameter, not the outside width of the housing. The housing dimensions listed for this selection are 137 × 115.5 × 54 mm.
Is SZ-M137-105DN an NPN normally open sensor?
Yes. SZ-M137-105DN is the NPN NO selection in the 105 mm range. Check the approved wiring diagram before connecting it to a controller.
Can it be used for counting fast-moving metal parts?
It may be evaluated for a counting station, but response time must be confirmed for the required throughput. Share the part geometry, travel speed and required timing with XSZ before selecting the sensor.
What information is needed to confirm the correct model?
Send the target material and dimensions, the path through the opening, line speed, supply voltage, controller input requirement and mounting or wiring drawing if available.




