Description
SZC-M30-10DN M30 shielded sensing
The XSZ SZC-M30-10DN is the M30 shielded, DC NPN normally open model in the supplied M30 range. It is listed with a 10 mm rated sensing distance (±10%) and a 0–8 mm setting distance for positioning the sensor relative to the intended target.
Choose this exact code when the controller requires an NPN NO signal and the machine layout calls for the shielded M30 version. Confirm the target material, sensing principle and mounting drawing before using the listed distance as the basis for installation.
Positioning the 10 mm shielded model
The 10 mm figure is the rated sensing distance; the source lists 0–8 mm as the setting distance for the shielded version. Set the detection point using the actual target and allow for target travel, mounting tolerance and repeatable presentation at the sensor face.
Shielded and non-shielded M30 models have different listed distances. The 20 mm non-shielded value belongs to a different model and should not be used to size the SZC-M30-10DN installation.
SZC-M30-10DN technical specifications
The values below are taken from the supplied M30 model and series table. Verify current ratings, target conditions and wiring against the exact-model datasheet before final design.
Sensing and output
| Model | SZC-M30-10DN |
|---|---|
| Thread / installation | M30 / shielded |
| Output | DC NPN, normally open |
| Rated sensing distance | 10 mm ±10% |
| Setting distance | 0–8 mm |
| DC response frequency | 0.5 kHz, source-listed for the M30 DC models |
Electrical data
| Supply voltage | 10–30 VDC |
|---|---|
| Supply ripple | Less than 10% |
| Leakage current | Less than 0.01 mA |
| Voltage drop | Less than 1.5 V |
| Switching hysteresis | Less than 15% of rated sensing distance |
| Indication | LED |
| Circuit protection | Short-circuit protection listed |
Housing and environment
| Housing | Nickel-plated copper |
|---|---|
| Sensing face | ABS |
| Operating temperature | 0 to +60 °C |
| Temperature drift | Less than 10% of rated sensing distance |
Related M30 model choices
The codes below are separate models in the supplied M30 table. They are not output or sensing-distance settings that convert the SZC-M30-10DN into another version.
| Model | Source-listed difference |
|---|---|
| SZC-M30-10DN2 | 10 mm shielded, NPN NC |
| SZC-M30-10DP | 10 mm shielded, PNP NO |
| SZC-M30-20DN | 20 mm non-shielded, NPN NO |
Application and installation checks
SZC-M30-10DN can be evaluated for presence and position feedback at an M30 machine mounting point when the actual target is compatible with this sensor. The available data does not establish which non-metal materials, if any, this exact model can detect; test the intended target rather than relying on a generic target list.
Before specifying this M30 model
- Confirm the sensing principle and the target material, size and position under operating conditions.
- Use the exact-model mounting drawing to check M30 thread engagement, face clearance and the 0–8 mm setting distance.
- Match the NPN NO output to the DC controller and confirm wiring, no-load current and maximum load current.
- Verify the protection class, connection type, cable routing and site temperature or moisture exposure.
Frequently asked questions
What distance is listed for SZC-M30-10DN?
Its shielded M30 entry lists 10 mm ±10% rated sensing distance and a 0–8 mm setting distance. Verify the actual target and mounting arrangement.
Is this model NPN normally open?
Yes. The supplied M30 table places SZC-M30-10DN in the DC NPN NO cell. PNP and NC choices use different model codes.
Can this model detect plastic or water?
Target compatibility for those materials is not established for this exact code by the available information. Confirm the sensing principle and test the real target before selection.
Can I use the 20 mm non-shielded rating?
No. That rating belongs to another M30 model. SZC-M30-10DN is the 10 mm shielded entry.







Reviews
There are no reviews yet.