SZ-M18-5DN M18 5 mm Flush Proximity Sensor

The XSZ SZ-M18-5DN is the 5 mm flush M18 DC NPN normally open model in the supplied proximity-sensor range. Its listed reference target is iron measuring 18 × 18 × 1 mm; the source lists 800 Hz switching frequency and 0.3 ms response time for the 5 mm group. The housing is nickel-plated brass with an ABS sensing face. Confirm supply voltage, exact body length and wiring for this code before installation.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M18-5DN product overview

The XSZ SZ-M18-5DN is the 5 mm flush M18 DC NPN normally open (NO) model in the supplied proximity-sensor range. Its 18 mm diameter format is intended for a close-range metal-detection point where the selected target and mounting gap match the sensor.

The listed 5 mm distance uses an iron reference target measuring 18 × 18 × 1 mm. Actual response can be shorter for other metals, target shapes and installation conditions. Confirm the exact supply, wiring and mechanical drawing for this code before installation.

Flush M18 metal detection at a listed 5 mm distance

The flush construction supports mounting the sensing face level with a suitable metal mounting surface. The 5 mm figure is a source-listed sensing distance, not a guaranteed working gap for every target. Test the real part at its planned clearance, especially if it is non-magnetic metal or smaller than the listed iron reference target.

For the 5 mm column, the supplied matrix lists 800 Hz switching frequency, 0.3 ms response time and 1% repeat accuracy. Check the full machine cycle and target motion before relying on these figures for a production process.

SZ-M18-5DN technical specifications

The data below comes from the supplied 5 mm column and shared M18 flush-series rows. Confirm it against the current exact-model datasheet where installation or electrical limits are critical.

Detection and mechanical data

ModelSZ-M18-5DN
Mounting / diameterFlush M18 / 18 mm
Listed sensing distance5 mm
Standard detection targetIron, 18 × 18 × 1 mm
Detectable targetMagnetic metal; sensing distance decreases for non-magnetic metals
Housing / sensing faceNickel-plated brass / ABS
Body lengthConfirm against the current drawing for this model

Output and sensing performance

Electrical type / outputDC NPN, normally open (NO)
Switching frequency800 Hz, source-listed for 5 mm models
Response time0.3 ms, source-listed for 5 mm models
Repeat accuracy1%, source-listed for 5 mm models
HysteresisLess than 10% of sensing distance
Supply and connectionConfirm voltage, pinout and cable for the exact model

Environment and insulation

Operating / storage temperature−30 to +65 °C; no freezing or condensation
Relative humidity35–95% RH, source-listed
Insulation resistanceAt least 50 MΩ at 500 VDC test, between energized parts and housing
Dielectric withstand test1000 VAC, 50/60 Hz, 1 minute, between energized parts and housing

Related flush M18 model codes

SZ-M18-5DN is the 5 mm DC NPN NO product on this page. The codes below are distinct output or sensing-distance selections in the supplied matrix, not settings that can be changed on this sensor.

ModelListed distanceOutput
SZ-M18-5DN — this product5 mmDC NPN NO
SZ-M18-5DN25 mmDC NPN NC
SZ-M18-5DP5 mmDC PNP NO
SZ-M18-5DP25 mmDC PNP NC
SZ-M18P-8DN8 mmDC NPN NO
SZ-M18P-12DN12 mmDC NPN NO

The source also lists separate DC two-wire and AC two-wire codes for the 5 mm and 8 mm columns. Their supply and connection requirements must not be applied to SZ-M18-5DN.

Installation and ordering checks

This flush M18 model may be evaluated for a defined metal-presence or position point on machinery. Check the actual metal, target size, mounting surface and available gap; the listed iron target is a test reference, not a promise of equal detection distance for every metal.

Confirm before installation

  • Use the exact-model drawing to confirm body length, thread and cable exit clearance.
  • Verify the supply voltage, NPN NO wiring diagram and permitted controller/load current.
  • Test the real target at the intended sensing gap and required machine speed.
  • Check the environmental exposure, cable specification and any required ingress-protection rating.

Frequently asked questions

Is SZ-M18-5DN the 5 mm NPN NO version?

Yes. The supplied model matrix places SZ-M18-5DN in the 5 mm DC NPN normally open row. NPN NC, PNP and two-wire versions have separate codes.

Does the 5 mm distance apply to every metal part?

No. The source uses an 18 × 18 × 1 mm iron reference target and says distance decreases for non-magnetic metals. Verify the real part at the planned gap.

Can I use the 8 mm or 12 mm specifications for this unit?

No. Those distances belong to different model codes in the same flush series. The listed 800 Hz, 0.3 ms and 1% figures are from the 5 mm column.

What electrical details still need confirmation?

The supplied material does not give an exact supply voltage, safe output-load rating or wiring diagram for SZ-M18-5DN. Check the current exact-model documentation before connecting it.

Reviews

There are no reviews yet.

Be the first to review “SZ-M18-5DN M18 5 mm Flush Proximity Sensor”

Your email address will not be published. Required fields are marked *