T-Type Slot Photo Sensor

The XSZ EUSL-U30 T-Type slot photo sensor is described for detecting opaque targets through a 30 mm gap with two optical axes. The supplied material lists separate NPN (`EUSL-U30R3C4-T`) and PNP (`EUSL-U30X3C4-T`) versions, a 10–30 VDC supply and pre-wired 2 m cable. Confirm the exact model, target geometry, channel output and current wiring diagram before selection.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

 

Category:

Description

T-Type slot detection with two optical axes

The XSZ EUSL-U30 T-Type series is a slot photo sensor described for detecting opaque targets as they pass through the sensing gap. Its two optical axes provide separate A/B detection channels for applications that need two position signals from one sensor assembly.

The supplied series data lists a 30 mm gap and an opaque target larger than Ø12 mm. Check the actual target shape, travel path and mounting drawing before choosing a model.

A/B signals for position checks

The source describes independent optical axes and separate channel signals. For an elevator-leveling or other position-detection arrangement, the controller can evaluate the two outputs as the target travels through the sensing region. The sequence and spacing must be checked against the machine’s actual geometry and controller logic.

Red and yellow status indicators are described for the channels. Confirm their exact correspondence and the Light-ON/Dark-ON control-wire setting in the current diagram for the selected model.

Technical specifications

The entries below come from the supplied EUSL-U30 T-Type series material. Confirm them against the current datasheet for the exact NPN or PNP code before wiring or machine design.

Detection and response

Detection formatT-Type slot photo sensor
Gap distance listed30 mm; confirm the dimension on the mounting drawing
Detectable object listedOpaque object larger than Ø12 mm
Optical axesTwo independent A/B channels
Response-time entry1 ms maximum, as stated in the source; confirm test conditions

Power and output

Supply voltage10–30 VDC
Supply ripple10% maximum, peak-to-peak
Control outputOpen collector; NPN or PNP according to model
Load current100 mA maximum
Operation describedLight-ON / Dark-ON selection by control wire; verify the wiring diagram

Construction and ambient-light entry

Case / lens materialABS / PC
ConnectionPre-wired 2 m cable
Channel indicators describedRed and yellow
Ambient sunlight entry10,000 lx maximum; confirm test conditions

Choose the NPN or PNP version

The source lists two separate -T model codes. Select the output type that matches the controller input; do not assume a single unit can change between NPN and PNP.

Model codeOutput listed
EUSL-U30R3C4-TNPN open collector
EUSL-U30X3C4-TPNP open collector

Application and installation checks

For an elevator-leveling or other position-detection point, confirm that the moving opaque target passes through the intended optical paths and produces the A/B signal sequence required by the controller. The actual mechanical clearance and response margin depend on the installation.

Before specifying a T-Type model

  • Confirm the target’s opacity, size, travel direction and position through both optical axes.
  • Check the 30 mm gap, channel spacing and mounting dimensions against the current drawing.
  • Select the NPN or PNP code and verify the exact channel and Light-ON/Dark-ON control-wire connections.
  • Check supply, load, 2 m cable routing, ambient light and required response under the actual operating conditions.

Frequently asked questions

Does one sensor provide two output channels?

The supplied series information describes two independent optical axes with separate A/B signals. Verify the exact channel wiring for the selected model.

Can the same unit switch between NPN and PNP?

The source lists separate NPN and PNP model codes. Choose the code required by the controller rather than assuming the output type can be changed on one unit.

What target size is listed?

An opaque object larger than Ø12 mm is listed. Confirm the object’s shape and travel path because the source does not provide the complete test arrangement.

How is Light-ON or Dark-ON selected?

The series description mentions selection by a control wire. Use the current wiring diagram for the exact model before connecting any conductor.