CR30-10DN CR30 10 mm Shielded Proximity Sensor

The XSZ CR30-10DN is a CR30 shielded proximity sensor with NPN normally open output and a 10 mm +/-10% sensing distance. The shielded CR30 model matrix also lists NPN, PNP, and AC two-wire NO and NC choices. Confirm cable, wiring, and target compatibility with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

CR30-10DN product overview

The XSZ CR30-10DN is a shielded proximity sensor with DC NPN normally open (NO) output. It is listed with a 10 mm ±10% sensing distance and a 0–8 mm setting distance using a 50 × 50 × 1 mm iron standard target. The shielded CR30 family also contains separate DC PNP and AC two-wire models.

For this model, match the NPN NO signal and 10–30 VDC supply to the controller, then check the actual metal target and installed gap. The red operating LED and 2 m cable are listed for the series; confirm the final wiring and mounting drawing before installation.

ModelCR30-10DN
ConfigurationShielded, DC NPN NO
Sensing distance10 mm ±10%
Standard targetIron, 50 × 50 × 1 mm

10 mm shielded sensing for a defined metal target

The listed 10 mm ±10% sensing distance is referenced to a 50 × 50 × 1 mm iron target. The 0–8 mm setting distance is the installation reference for positioning the sensor. A smaller part, different material or different approach path can change the switching point, so confirm the actual target at the intended gap.

Shielded describes the CR30-10DN configuration in the model table; it does not replace the need for the current mounting drawing. The listed mechanical designation is “CR30,” without full dimensions or a mounting-thread specification.

Technical specifications

The electrical values below are the listed DC values for the CR30 range. Confirm the current CR30-10DN datasheet before connecting a controller or selecting the final mounting gap.

Detection and installation data

Mechanical designationCR30; confirm full drawing dimensions
ShieldingShielded
Sensing distance10 mm ±10%
Setting distance0–8 mm
Standard detection targetIron, 50 × 50 × 1 mm
HysteresisNo more than 20% of sensing distance
Operating indicatorRed LED
Cable length2 m

DC NPN electrical data

Output logicNPN, normally open (NO)
Rated supply voltage10–30 VDC
Current consumptionMaximum 15 mA for DC type
Control output200 mA for DC type; confirm load compatibility
Response frequency50 Hz for DC type
Residual voltageMaximum 1.5 V for DC type

Environment and electrical safety

Operating temperature−10 to +70 °C; no freezing or condensation
Storage temperature−30 to +80 °C; no freezing or condensation
Ambient humidity35–95% RH
Insulation resistanceMinimum 50 MΩ at DC 500 V
Withstand voltage1500 VAC, 50/60 Hz for 1 minute

Mechanical endurance and temperature influence

The listed vibration test is 1 mm amplitude at 10–55 Hz in X, Y and Z directions for 2 hours each. The listed shock test is 500 m/s² (50 G), three times in each X, Y and Z direction.

Across −10 to +70 °C, sensing-distance temperature influence is listed within ±20% of the value at +20 °C. Confirm the target and test conditions when applying this figure to the installed gap.

Related CR30 shielded models

CR30-10DN is the DC NPN NO product on this page. The remaining codes are separate NPN, PNP or AC two-wire selections. They require the supply and controller interface specified for each model rather than a change of setting on CR30-10DN.

Electrical typeLogicModel
DC NPNNOCR30-10DN — this product
DC NPNNCCR30-10DN2
DC PNPNOCR30-10DP
DC PNPNCCR30-10DP2
AC two-wireNOCR30-10AO
AC two-wireNCCR30-10AC

Applications and installation checks

CR30-10DN can be evaluated for detecting an iron target at a defined position in industrial equipment. Check the target’s material, size and travel path against the 50 × 50 × 1 mm reference target; a different target may produce a different switching gap.

Before specifying CR30-10DN

  • Confirm the DC NPN NO output matches the controller and obtain the model-specific wiring diagram.
  • Check the actual target and installed gap against the listed sensing and setting distances.
  • Verify CR30 mounting dimensions, cable termination and the red LED position on the approved drawing.
  • Check supply, load current, response requirements and the operating environment before ordering.

Frequently asked questions

Does the 10 mm rating apply to every metal target?

No universal target claim is provided. The listed distance uses a 50 × 50 × 1 mm iron standard target. Confirm the actual material and shape at the planned gap.

What output does CR30-10DN provide?

The model matrix identifies it as DC NPN normally open. NC, PNP and AC two-wire versions have different model codes.

What mechanical size does CR30 mean?

CR30 is the format designation listed in the available product table. Confirm body, mounting and sensing-face dimensions from the current drawing.

What should be checked for the controller connection?

Confirm the NPN NO input, 10–30 VDC supply, load current, residual voltage, response frequency and wiring for CR30-10DN.

Reviews

There are no reviews yet.

Be the first to review “CR30-10DN CR30 10 mm Shielded Proximity Sensor”

Your email address will not be published. Required fields are marked *