SZ-M68-3DN 3 mm Detection-Hole Sensor, NPN NO

XSZ SZ-M68-3DN is a 3 mm detection-hole sensor with a 0.5 mm minimum detection target and NPN normally open output. The source-listed 3 mm selection also includes NPN NC, PNP NO, and PNP NC models. The source drawing shows a 39 x 68 x 20 housing with two 5.6 mm mounting holes at 28 mm spacing. Confirm cable, wiring, target material, and installation clearance with XSZ before order.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

SZ-M68-3DN product overview

The XSZ SZ-M68-3DN is a 3 mm detection-hole sensor with an NPN normally open (NO) output. The listed minimum detection target is 0.5 mm, with iron specified as the standard detection target. Its operating supply range is 10–30 VDC.

This model is intended for a detection point where a small target passes through the opening. Check the actual target material, size, alignment and controller input before selecting it; the listed minimum is not a guarantee for every material or operating condition.

ModelSZ-M68-3DN
Detection opening3 mm
Minimum detection target0.5 mm, subject to target conditions
OutputNPN NO

3 mm opening for small-target passage detection

The 3 mm figure describes the detection-hole diameter, not an external housing dimension. The target must pass through that opening with suitable mechanical clearance and a repeatable path. The 0.5 mm minimum-target value should be checked against the actual target material, shape and movement before it is used as a selection limit.

The standard detection target is listed as iron. If the application uses another material or a different target geometry, send XSZ a sample or the target details for confirmation rather than assuming the same detection result.

Technical specifications

Use the current SZ-M68-3DN datasheet and drawing to confirm the electrical interface, target conditions and mounting geometry before finalizing a machine design.

Detection and mounting dimensions

Product typeDetection-hole sensor
Detection-hole diameter3 mm
Minimum detection target0.5 mm
Standard detection targetIron
Drawing dimensions39 × 68 × 20 (confirm units and orientation on current drawing)
Mounting holes2 × Ø5.6 mm; 28 mm center spacing
AdjustmentSide adjustment screw

Electrical specifications and protection

Output configurationNPN, normally open (NO)
Operating voltage10–30 VDC
Consumption current15 mA
Load current100 mA maximum at DC 24 V
Listed circuit protectionReverse-connection protection, surge absorption and load short-circuit protection

Operating environment and insulation

Operating and storage temperature−30 to +65 °C; no freezing or condensation
Operating and storage humidity35–95% RH
Insulation resistanceAt least 50 MΩ at DC 500 V, between energized parts and housing
Protection classIP67 (IEC)

Temperature and voltage influence

Temperature influence−30 to +65 °C: within ±15% at +23 °C;
−25 to +60 °C: within ±10% at +23 °C
Voltage influenceWithin ±15% of rated supply-voltage range; within ±10% sensing distance at rated supply voltage

Related 3 mm detection-hole sensor models

SZ-M68-3DN is the NPN NO unit described here. The other codes below are separate output selections in the 3 mm group, not switchable modes of this model.

Output typeLogicModel
NPNNOSZ-M68-3DN — this product
NPNNCSZ-M68-3DN2
PNPNOSZ-M68-3DP
PNPNCSZ-M68-3DP2

Applications and installation checks

Typical applications

  • Checking the passage of a small target through a 3 mm opening.
  • Providing a part-presence signal at a compact assembly station.
  • Supporting a small-part counting task after target and response-time validation.

Installation considerations

Allow for two Ø5.6 mm mounting holes at 28 mm center spacing and access to the side adjustment screw. Check the current drawing for the housing dimension units, mounting orientation and cable exit before preparing the mounting plate.

What to confirm before ordering

  • Actual target material, cross-section, orientation and path through the 3 mm opening.
  • The conditions behind the 0.5 mm minimum-target figure and any required response time.
  • 10–30 VDC supply, NPN NO controller input and the wiring diagram.
  • Drawing units, mounting clearance, cable arrangement and ambient conditions.

Frequently asked questions

What does the 3 mm dimension describe?

It is the diameter of the detection hole, not the outside size of the housing.

Does the 0.5 mm minimum apply to every target material?

Not necessarily. Iron is the listed standard target. Confirm detection with the actual material, shape and operating conditions before selecting the sensor for a 0.5 mm target.

Is SZ-M68-3DN the NPN normally open model?

Yes. SZ-M68-3DN is the NPN NO option. The NC and PNP options have their own model codes, and the current wiring diagram should be checked before connection.

What mounting information is available?

The listed drawing values are 39 × 68 × 20, with two Ø5.6 mm holes at 28 mm center spacing and a side adjustment screw. Confirm the dimension units and orientation on the current drawing.

Reviews

There are no reviews yet.

Be the first to review “SZ-M68-3DN 3 mm Detection-Hole Sensor, NPN NO”

Your email address will not be published. Required fields are marked *