Professional Industrial Sensor Manufacturer
XSZ Sensor

XSZ engineering tool

Sensor Cable Voltage Drop Calculator

Estimate how much DC supply voltage is lost along a sensor cable, then compare the remaining voltage with the minimum required by your exact sensor model.

Calculate the supply path

Enter the worst-case values

Use the lowest supply voltage expected at the cable origin and the current and conductor resistance expected in operation. This is a low-voltage DC cable estimate, not a wiring approval.

Advanced: different currents in +V and 0V conductors

For a three-wire sensor or shared circuit, these conductors may carry different currents. Enter the actual current in each wire; do not assume the output lead’s current flows in both supply wires. Output-signal voltage is not calculated.

When both advanced fields are filled, they replace the basic current value. Leave both blank to use basic mode.

What this calculator measures

A DC conductor has resistance. Current through the supply wire and return wire creates voltage drop in both, so the voltage across the sensor can be lower than the voltage at the panel.

Cable drop (V) = [one-way length (m) ÷ 1,000] × resistance per conductor (Ω/km) × [(+V current + 0V current) ÷ 1,000]Currents are entered in mA. In basic mode the two currents are equal, so this simplifies to 2 × length × conductor resistance × current, with unit conversions. Sensor voltage = supply at origin − cable drop.

One-way is not loop length

Measure the installed run once from panel to sensor. The basic calculation accounts for both +V and 0V conductors; doubling the entered length again would double-count the loop.

Use cable-specific resistance

Conductor diameter alone does not capture every cable construction or temperature. Use a manufacturer’s per-conductor resistance for the actual cable, ideally adjusted or measured for operating conditions.

Compare with the sensor limit

Use the exact model’s minimum supply voltage—not a generic percentage rule. A calculated margin is only one part of a complete wiring and operating check.

Why check voltage drop before installing a long cable?

A circuit that appears fine at a bench supply may reach a lower voltage at the remote sensor, especially when the source is at its low end or current rises during operation.

Step 1

Choose the low-end supply

Measure or specify the minimum voltage available at the cable origin under realistic loading. A nominal “24 V” label may not describe the worst case.

Step 2

Trace the current path

In a simple two-conductor feed, outgoing and return currents match. With a three-wire NPN/PNP sensor or shared supply, trace which wire carries each current.

Step 3

Measure at the far end

After installation, measure across the sensor’s +V and 0V terminals while the machine runs. Compare that reading with the model range and the calculation.

Worked example

Illustrative cable-only case: a 50 m one-way run, 100 mA in both conductors, 58 Ω/km per conductor and 24 V at the cable origin.

Each wire: 50 ÷ 1,000 × 58 = 2.9 Ω. Loop: 5.8 Ω. Cable drop: 0.100 A × 5.8 Ω = 0.58 V. Estimated sensor supply: 23.42 V.The 58 Ω/km value is an example maximum for a specific Phoenix Contact 0.34 mm² sensor cable at 20 °C—not a universal value for every 0.34 mm² cable. Connector and warmer-cable losses are excluded.

Long conveyor run

Estimate loss from a distant control cabinet to a photoelectric sensor, then measure voltage at the sensor while the conveyor is operating.

Several devices on one feed

Each cable segment carries the current of devices downstream from it. Model segments separately; a single sensor-current entry cannot represent the whole shared network.

Three-wire proximity sensor

Use the advanced inputs only after tracing +V and 0V currents. Check the separate NPN/PNP output-wire path and PLC input thresholds independently.

Frequently asked questions

Should I enter cable length once or twice?

Enter the one-way panel-to-sensor length once. In basic mode, the formula includes both the outgoing +V wire and returning 0V wire.

Does a positive voltage margin prove the sensor will work?

No. It only compares this cable estimate with the specified minimum sensor supply. Confirm the exact model’s maximum voltage, current, output type, load, PLC input, transient conditions and measured voltage at the terminals.

Can I use wire gauge instead of Ω/km?

The tool asks for resistance because cable construction and temperature matter. Find the maximum conductor resistance in the actual cable datasheet or use a suitable measured value; do not assume one resistance for every cable with the same nominal gauge.

Does the tool include the NPN or PNP output wire?

No. It estimates the sensor supply between +V and 0V. The separate output lead, PLC input threshold, load wiring and any voltage drop along that signal path require their own circuit check.

What about connector and splice resistance?

They are excluded. Poor contacts, extra connectors and corrosion can add loss. Measure the installed circuit under load and investigate any difference from the cable-only estimate.

Can I use this for AC, IO-Link or a safety circuit?

Not as an approval tool. The calculation is a steady-state DC conductor estimate. AC impedance, IO-Link communication behavior, safety requirements, transients and voltage ripple need the relevant system documentation and testing.

Need help with a long sensor run?

Share the sensor model, cable part number and length, supply range, current path, connector count and controller input. XSZ can review the full installation requirements.

Ask XSZ engineering

Technical background: Fluke, voltage drop and Ohm’s law; Fluke, outgoing and return conductor losses; Phoenix Contact, example sensor-cable resistance. These sources explain the method and one example cable; they are not XSZ model specifications.