Professional Industrial Sensor Manufacturer
XSZ Sensor

XSZ engineering tool

Ring Proximity Sensor Selector

Find a listed aperture that can clear your part or feed tube, then identify the sensing and controller checks needed before choosing an inductive ring sensor.

Start with your feed path

What has to pass through the ring?

Enter the largest outside diameter that must clear the opening. This may be your tube outside diameter, not the metal part diameter. All dimensions are in millimetres.

Optional details for a better review

Why a ring sensor—and why a fit check is not enough

An inductive ring sensor detects metal passing within its opening. Selecting one involves a mechanical path and an electrical detection problem, which should be checked separately.

Clear the whole feed path

Use the outside diameter of a feed tube if it goes through the ring. Add your own installation and tolerance allowance. The tool compares this requirement with listed XSZ aperture sizes.

Test the real metal target

Part material, smallest section, orientation and position can change detection. A small part near the centre of a large opening deserves particular bench testing; bore size alone cannot predict sensitivity.

Match the signal chain

Counting requires a usable pulse at the actual part speed and spacing. Confirm the chosen model’s response, output type and the controller input settings. Stationary presence may call for a different operating mode.

How to use this selector

The result is a shortlist for engineering review, not a certified SKU recommendation.

Step 1

Measure the envelope

Record the tube or part’s largest outside diameter at the sensing point and decide the extra diametral clearance your mechanics need.

Step 2

Screen the aperture

Compare the required clear diameter with XSZ’s listed openings. Prefer the smallest opening that truly fits, then consider the next larger listed size if installation needs it.

Step 3

Validate sensing and output

Pass the smallest real parts through at production speed and worst-case position. Check metal type, pulse width, NPN/PNP compatibility and installation effects against the exact datasheet.

Typical selection situations

The feed geometry changes what you should enter—and what you must verify after the initial screen.

Screws through a plastic tube

Enter the tube’s outside diameter, not the screw head width. Then test the shortest or smallest screw at its actual off-centre position and feed rate.

Loose springs in a chute

Allow for the spring’s largest passing orientation. If counting fast, low-mass parts, review whether the selected model supports the necessary dynamic response.

Metal part present in the opening

A static presence task is different from counting a transient part. Confirm the exact model’s operating mode and whether surrounding metal can affect the installation.

Frequently asked questions

Does a 30 mm part require a 30 mm ring?

No. A 30 mm outside diameter leaves no diametral clearance in a 30 mm nominal opening. Include the actual part or tube envelope, tolerances and your required allowance, then choose a listed opening that physically clears it.

Will the smallest ring that fits always detect the part?

No. The initial size check is mechanical only. The smallest target cross-section, material, orientation and path can affect sensing. Test representative parts using the exact candidate model and its datasheet.

Can an inductive ring sensor detect plastic parts?

Not as a direct inductive metal target. If the only target is non-metal, review another sensing principle or a suitable detectable metal feature with engineering support.

Can one ring count parts and monitor a jam?

Possibly, but the operating mode and control logic matter. Static presence and dynamic passage sensing are not interchangeable on every model. Confirm the model behavior and test both conditions.

Does a model name ending in DN prove it matches my PLC?

No. Even when a public product title names NPN NO, confirm the actual datasheet, supply voltage, wiring, load and PLC input common. This tool does not infer undocumented output variants.

What if no listed opening fits my tube?

The tool will not force a smaller size. Share the required clear diameter, tube material, target details and mounting constraints with XSZ to review another size or sensing arrangement.

Need a model-specific check?

Send the tube outside diameter, metal part drawing or photo, smallest target, path, passage speed and controller input details. XSZ engineering can review aperture and detection together.

Ask XSZ engineering

Technical background: Pepperl+Fuchs, inductive ring sensor design; ifm, ring sensor applications and static/dynamic operation. XSZ aperture links above reflect the new-site product list checked for this local draft; reconfirm each live product page before publication.