E3FA-TN12 ABS Reflective Photoelectric Sensor

OMRON E3FA-TN12 2M is an infrared through-beam photoelectric sensor set with an emitter and receiver. It offers a rated 15 m sensing distance, NPN open-collector output, 10–30 VDC supply, selectable Light-ON/Dark-ON operation and 2 m pre-wired cables. Use the model-specific wiring instructions to match the receiver output to the controller input.

  • Factory Direct Supply
    Stable Quality
  • Custom Options
    Support OEM/ODM
  • Technical Support
    Quick Response

Description

OMRON E3FA series

E3FA-TN12 2M infrared through-beam detection

The E3FA-TN12 2M is a through-beam photoelectric sensor set, not a reflective sensor. Its emitter and receiver face each other across the detection path; an opaque object is detected when it interrupts the beam. The rated sensing distance is 15 m, with NPN output and 2 m pre-wired cables.

A separate emitter and receiver for presence detection

Mount the emitter and receiver opposite one another so the intended part passes through the infrared beam. OMRON specifies an opaque object of at least 7 mm diameter as the standard sensing target. Actual performance depends on alignment, target geometry and site conditions, so test the installed detection point with the real part.

The set is identified by model E3FA-TN12 2M. Its component designations are E3FA-TN12-L 2M for the emitter and E3FA-TN12-D 2M for the receiver. Confirm whether the purchase order and supplied package refer to the complete set or an individual component.

Technical specifications

Detection and output

ParameterE3FA-TN12 2M
Detection methodThrough-beam, emitter/receiver set
Rated sensing distance15 m
Standard sensing objectOpaque object, 7 mm diameter minimum
Light sourceInfrared LED, 850 nm
OutputNPN open collector; load current 100 mA max.
Operating modeLight-ON / Dark-ON, selectable by wiring
Response time0.5 ms

Power, connection and construction

ParameterE3FA-TN12 2M
Supply voltage10–30 VDC; ripple 10% (p-p) max.
Current consumption40 mA max. total (emitter 25 mA, receiver 15 mA max.)
ConnectionPre-wired, 2 m cable
Housing / lensABS / PMMA
Thread / product lengthM18 / 41 mm
Degree of protectionIP67 / IP69K
Operating temperature−25 to +55 °C (no icing or condensation)
Storage temperature−40 to +70 °C (no icing or condensation)

Selection and installation checks

Use the 15 m rating to plan the separation between the emitter and receiver, then verify beam alignment and target interruption at the machine. Through-beam sensing is useful to evaluate for part-presence, passage or position checks on conveyors and automation equipment when the target can pass between two mounting points.

Match the NPN receiver output and 10–30 VDC supply to the controller. Follow the supplied wiring instructions for Light-ON or Dark-ON operation and keep the connected load within the specified 100 mA limit. If the controller needs PNP output, OMRON lists E3FA-TP12 2M as a separate model.

Frequently asked questions

Is the E3FA-TN12 2M a reflective sensor?

No. It is a through-beam model with separate emitter and receiver units. The object is detected as it interrupts the beam between them.

Does the set include both sensing units?

OMRON lists E3FA-TN12 2M as a set containing emitter E3FA-TN12-L 2M and receiver E3FA-TN12-D 2M. Check the order and package if a single replacement unit is needed.

Can its output be changed from NPN to PNP?

No. E3FA-TN12 2M is the NPN model. E3FA-TP12 2M is the separate PNP set; Light-ON/Dark-ON selection does not change the output transistor type.

What must be checked before wiring it to a PLC?

Confirm the PLC input type, supply voltage, load current and the required Light-ON/Dark-ON wiring against the model-specific instruction sheet.